Tune questions

[telibyte]

I had a previous mail order tune from here. KenB should remember me. ( I bought his old 2v heads a long time ago) I do not know where my paperwork is from way back then. I ordered the xcal 1.

1. Do you still support mail order tunes for xcal 1?
2. Will I fall under the $40 mail order tune?
3. Can you do a 4v base tune for the mods below that is good enough to get me to a dyno?
4. Can you do a tune for mods below to make it everyday drivable? ( I don't think there are any dyno tuning shops near my location)

99 GT swapped to a 4v

96 Teksid block bored .020 over
Completely balanced rotating assembly
Diamond forged Aluminum FT with 4V reliefs
Manley H-beam rods with arps bolts
Federal Mogul performance bearings
99 GT cast crank
03 Aviator/Cobra heads Intake,Exhaust, and bowls have been cleaned up and polished.
Stock valves
Crower retainers and high lift springs
Crower stage 3 N/A cams
30lb injectors
3.73 gears, but will probably upgrade to 4.10's or taller
01+ cobra intake
Aluminum Flywheel
Hooker coated LT's with o/r x-pipe
Flowmaster Delta catback

Thanks
Jason

[telibyte]

I am also going to need a tune fairly quick... Any word?

[telibyte]

Do I need to call to to find this out?

[telibyte]

I had a previous mail order tune from here. KenB should remember me. ( I bought his old 2v heads a long time ago) I do not know where my paperwork is from way back then. I ordered the xcal 1.

1. Do you still support mail order tunes for xcal 1?
2. Will I fall under the $40 mail order tune?
3. Can you do a 4v base tune for the mods below that is good enough to get me to a dyno?
4. Can you do a tune for mods below to make it everyday drivable? ( I don't think there are any dyno tuning shops near my location)

99 GT swapped to a 4v

96 Teksid block bored .020 over
Completely balanced rotating assembly
Diamond forged Aluminum FT with 4V reliefs
Manley H-beam rods with arps bolts
Federal Mogul performance bearings
99 GT cast crank
03 Aviator/Cobra heads Intake,Exhaust, and bowls have been cleaned up and polished.
Stock valves
Crower retainers and high lift springs
Crower stage 3 N/A cams
30lb injectors
3.73 gears, but will probably upgrade to 4.10's or taller
01+ cobra intake
Aluminum Flywheel
Hooker coated LT's with o/r x-pipe
Flowmaster Delta catback

Thanks
Jason

I am also using the 99 GT stock MAF, and an 03 Mach 1 stock intake tube...
I will pm u my PCM code later.
Thanks
Jason

[Nancye]

I have an answer :thumb: and it is good news!

[telibyte]

Can u please pm me the details, and I can then pay you and get my car up and running :):):):):):) :)
O and TY

[telibyte]

All I can say is
YOU GUYS ROCK :)

[telibyte]

Any word on an ETA for my tune?
Thanks
Teli

[telibyte]

Any word on an ETA for my tune?
Thanks
Teli

Hmm no response since May 8th

[03WhiteGT]

Hmm no response since May 8th

No response here either. :mad:

[telibyte]

Still waiting here

[telibyte]

July 22 still waiting.....

[03WhiteGT]

I dont think they pay attention to whats posted here anymore.

[mystichris@MD]

We sent the .xtr file to your e-mail on 4-30-08. If there were any other problems we were not aware of them. Send me a message if there is anything else that you need.

Chris

[telibyte]

Can you pm me your e-mail? I will send you all the e-mails I sent to ken, nancey, and Kelly. How ever you want to proceed forward is fine with me.
Not one response back.

Thanks
Teli