My 99 Saleen HP 57mm TT kit

[S281#124]

ENGINE:
assembled @ HCI motorsports
TEKSID block .30 over
manley rods
manley 21.5cc dished slugs
04 race prepped crank
VT stage III heads
Comp stage II blower cams
cobra oil pump
Canton 7qt pan
Reichard Racing intake
80mm TB
SCT 2800 M/A
75lb inectors


I just went from a KB 1.7 to a HP 57mm Turbo kit. Been about a yr since I drove the car and Im real close to haveing it all together, Thanx TOM and to many other MD member's who I've bought parts from and knowledge that was passed down to me:usa:

http://i31.photobucket.com/albums/c352/VirgilB/Saleen001-2.jpg

http://i31.photobucket.com/albums/c352/VirgilB/Saleen006.jpg

http://i31.photobucket.com/albums/c352/VirgilB/Saleen001-1.jpg

http://i31.photobucket.com/albums/c352/VirgilB/Saleen002.jpg

http://i31.photobucket.com/albums/c352/VirgilB/Saleen002-1.jpg

[98saleennc]

Nice choice and build!

Ryan
:headbang:

[S281#124]

well did a bit of wrench'n today, Plumbed my oil return line with -12 aeroquip line, Same as my fuel lines.

http://i31.photobucket.com/albums/c352/VirgilB/pics022.jpg

http://i31.photobucket.com/albums/c352/VirgilB/pics023.jpg

http://i31.photobucket.com/albums/c352/VirgilB/pics024-1.jpg

http://i31.photobucket.com/albums/c352/VirgilB/pics025-1.jpg

I was just play'n around here not sure if Im going to keep it or not :2guns:

http://i31.photobucket.com/albums/c352/VirgilB/pics020.jpg

[WildPony98]

are you planning on getting Turbo grinds or are you going to keep the blower cams?

[y2k2gt]

You are installing a scavenge pump, Right. Looks like your ready to make 800+rw.

[S281#124]

are you planning on getting Turbo grinds or are you going to keep the blower cams?

Well we have taken that into consideration, I am running stage II blower cams from comp. We are going to run it for awhile atleast untill I get this motor broke in, Then I will ultimately leave it up to my Tuner(forcefedperformance.com). I'll keep you posted on what we end up with :thumb:

[S281#124]

sHE FIRED RIGHT UP TODAY, I just let it idle for a few sec's to make sure there where no oil leaks. A few more little things and off to the tuner for a base tune (no boost).


http://i31.photobucket.com/albums/c352/VirgilB/pics037-1.jpg

http://i31.photobucket.com/albums/c352/VirgilB/pics036-1.jpg

http://i31.photobucket.com/albums/c352/VirgilB/pics035.jpg

[S281#124]

Finally got her tuned with a brake in tune since the motor only has 45 miles on it.
@ 4K RPM, 1/2 throttle , 4lb's of boost = Made 370hp on pump gas

Note: I do have 22cc dished pistons and and run about 8:1

[y2k2gt]

Nice! This was how mine was broke in.
http://forums.modulardepot.com/showthread.php?t=104912

[S281#124]

Nice! This was how mine was broke in.
http://forums.modulardepot.com/showthread.php?t=104912

Right,new bearings though. I have file fit rings so I think I will be gentle and brake things in alittle. How's she run now?

[y2k2gt]

I installed new file fit rings. The cylinders were honed also, so just like a complete new engine. Right now I'm still waiting for MD to finish up the new mods. Here is how it ran before taking it to MD for mods.
http://s160.photobucket.com/albums/t165/y2k2gt/?action=view&current=100_1656.flv